Inspected damages: visual inspection of the aircrafts which are present in the hangar: damages of a fuselage, of an engine, of a wing, of a tail unit, of a landing gear. Accident emergency landings (on ground and on water); emergency water landings.
Аннотация к работе
National Aviation University Aerospace Institute Aircraft Maintenance Department Practice report Inspection of malfunctions and damages of the aircraft Done by: Oleksandr Krasnoshchok, Karolina Chelpanova, Stanislav Pashnyak Group: FLA-106 Checked by: L. Zhuravlova Kyiv 2012 Content Introduction Part 1. Inspected damages Our visual inspection of the aircrafts which are present in the hangar of NAU9 1.1 Damages of a fuselage 1.2 Damages of an engine 1.3 Damages of a wing 1.4 Damages of a tail unit 1.5 Damages of a landing gear Part 2. What to do while accident? Emergency landings (on ground and on water) Emergency water landings Conclusion REFERENCES INTRODUCTION Damages are serious problem in aviation. Great amounts of damages cause improper operation of an aircraft or even to the catastrophes. The aircraft engineers have to carry out some technical maintenance to get rid of all the things which may cause the improper operation of an aircraft. Different types of operations are used to prevent damages formation. Aircraft damages can be classified into different classes: dents, nicks, scratches, cracks, holes, abrasions, gouges, corrosions, notes, delamination, disbonds. A Dent is depressed or hollow deformations without removal of material or change in cross sectional area. Generally dents are caused by impact from a smoothly contoured object. One characteristic that all dents should have is a pushed in surface and a relatively smooth bottom where metal is not displaced, folded or creased. Many Aircraft Structural Repair Manuals specify that a crease be treated as a crack. Generally when evaluating dents, the width of the dent is the second longest distance across the dent, measured at 90 degrees to the direction of the length. Nicks are broken edges without cracks, but with portions of material removed. Negligible damage limits will vary with structure, material, and loading. Scratches are marks penetrating the surface that reduce the structural cross section of the material but do not penetrate the complete thickness. The depth of a scratch may be determined by use of an optical micrometer. Generally, scratches in Alclad aluminum alloy sheet that do not penetrate the protective Alclad layer are classified as negligible. Cracks are fractures that would not separate the material into two parts if the surrounding supports were removed; usually originating at edges, holes, or points where concentrated loads are applied or where abrupt changes in cross-sectional area occur. Cracks cause a significant cross-sectional area change. This damage usually has an irregular line and is often the result of fatigue in the material. The length of cracks that may be tolerated varies widely with material, structure, and application. No crack should be regarded as negligible until the damage limits for the affected structure have been determined Holes are punctures, penetrations or cutouts that breach the complete thickness of the material and is fully surrounded by undamaged material. The size, shape, and distance from edges and supporting structures must be considered when evaluating hole damage. Abrasion is a damaged area that is the result of scuffing, rubbing, scraping, or other surface erosion. This type of damage is usually rough and has an irregular shape. Gouge is a damaged area where the result is a cross-sectional change caused by a sharp object and gives a continuous, sharp or smooth groove in the material Corrosion is a deterioration of a metal because of an electrochemical reaction with its environment. Depending on the type of corrosion, this deterioration may take the form cracking, exfoliation, or erosion of the corroding material. Corrosion damage is typically classified as light, moderate, or severe, depending on the extent of the corrosion and the loading requirements of the corroded part. Aircraft-specific structural manuals should be consulted for the correct classification of corrosion damage on a given part. Not: is an initial accurate determination of the type of damage encountered can usually be made by the use of a 10X magnifying glass or an optical micrometer. True crack length determination will generally require some form of Non Destructive Testing such as Eddy Current or Fluorescent penetrants. Delamination is a separation of the layers of material in a laminate, either local or covering a wide area, that occurs during manufacturing or in service. Fiber-reinforced and composites may delaminate when impacted and not exhibit visible damage. Disbond is an area within a bonded interface between two adherents in which an adhesion failure or separation has occurred. If the separation is performed deliberately to referred to as a debond. An aviation accident is defined as an occurrence associated with the operation of an aircraft which takes place between the time any person boards the aircraft with the intention of flight until such time as all such persons have disembarked, in which a person is fatal